The Partitions feature allows you to divide the area into partitions and manage them. This allows for separate arming and disarming of each created area. Maximum of four and minimum of one partitions can be created. You can add users, sensors, keyfobs and keypads to the each partition.
The Partitions page lists the created partitions, along with the number of Users, Sensors, Keyfobs and Keypads associated with them. You can click on each section to access them.
To view a partition:
In the
AlarmNet 360 home page,
type the City-CS-Sub
or MAC ID of
the device and then click Search.
The account number, along with the device details, appears.
Under
Actions, select
Edit and then click
the 
icon. The Account Overview
page appears.
In the left pane, click Partitions.
The summary page with the list of created partitions is displayed. You can click on each partitions displayed on the menu bar to access them.
This feature allows you to make a partition as a common among all the created partition. You can select Common Partition option while creating the partition.
|
Note: You can make third or fourth partition as a common partition. |
The Add option lets you create a new partition.
To add a new partition,
In the Partitions page, click Add displayed in the menu bar.
Enter the name and description of the partition in the respective fields.
You can define the following options:
Field |
Description |
Entry Delay1 |
From the list, select to specify the entry delay 1. The entry delay time gives you time to disarm the system when you reenter through the entrance door programmed as the entry delay door. |
Entry Delay2 |
From the list, select to specify the entry delay 2. The entry delay time gives you time to disarm the system when you reenter through the entrance door programmed as the entry delay door. |
Exit Delay |
From the list, select to specify the exit delay. Exit delay gives you time to leave through the designated exit door (after the System is armed) without setting off an alarm. |
ArmingDing |
From the list, select to confirm the arming through the following options:
|
Quick Arm |
Select to arm the panel from the downloader. You have to specify the area, when prompted. |
Quick Exit |
Select to enable the user to exit an armed premise quickly without disarming and rearming the system. When the Quick Exit sequence is entered, if the system had been armed, it restarts exit time in that specific partition as if it was just armed. All rules of exit apply including the exit error logic. |
Restart Exit Time |
Select to restart the quick exit time. |
Force Bypass |
Select to enable you to select the zone(s) that you wish to bypass. The bypass feature can be used when you want to intentionally arm your system with one or more zones unprotected. |
Silent Exit |
This option is disabled depending on the selected device type. |
Display Exit Time |
Select to display the exit delay time on the keypad. |
Chime Mode |
This option is enabled depending on the device type. |
Power Up in Previous |
When the system powers up armed, an alarm will occur 1 minute after arming if a zone is faulted, and any bypassed zones will be unbypassed. This is a read-only field. Note: If the previous state was Armed Away or Stay, the system will not respond to sensor changes for 1 minute. This allows time for sensors such as PIRs to stabilize. |
Auto Stay Arming |
If this feature is enabled by installer, the panel, when armed AWAY from the control’s keypad or a Wireless Keypad, automatically switches to the STAY mode if the Exit Time expires and no exit has been made. Exit must be made through an Entry/Exit Zone (door). If exit is made through a Garage Door, the system will automatically switch to the STAY mode when the Exit Time expires. Note: If the exit route entry/exit sensor is in a check condition or has been bypassed it will result in a loss of interior protection because the alarm system will arm STAY in this case. Consult with your installer for servicing of the entry exit zones or to turn off this feature if a check condition on entry exit zones occurs. |
Click on Users, Sensors, Keyfobs, and Keypads to access the respective page and add them to the partition.
Click Save to add the partition.
You can edit the partition by accessing them individually from the Partitions page.
To edit a partition,
In the Partitions page, click on the name of the required partition to edit them.
Edit the required details and click Save.
To delete a partition, click Delete in the required partition page and click Ok in the confirmation pop-up.
